D-STAR Kenwood TH-D74A

D-STAR Kenwood TH-D74A

I was in the market for an HT and decided to take a look at what the “Big 3” were offering. My attention was drawn to the D-STAR Network after stumbling into a D-STAR video featuring the ICOM ID-51A.  After a little more research it became apparent the best choice for me would be the D-STAR Kenwood TH-D74A.

D-STAR KENWOOD TH-D74A
Kenwood TH-D74A – Tri-Band APRS/GPS/D-STAR

First rule of D-STAR: You must register!

I registered through HRO where I purchased the radio, and within a business day my registration was working. The D-STAR network checks for a valid callsign registration before allowing access. So you can’t work any D-STAR without the validated registration. It took less than 5 minutes to enter the basic required info via the web. I entered my info on a weekend, and it was working after the following business day.

D-STAR Gateways

The ‘gateway’ function was what really got me going on D-STAR. The digital repeaters have an internet gateway function that allows for connection to remote D-STAR repeaters and ‘reflectors’ around the world. Count me in! This is a must have capability at K6HR.

Finding my local digital repeaters was simple, and I quickly determined which repeaters I could access. The GPS feature enables you to find the local repeaters with the press of a button from a built-in database. Pretty slick!

However…

I also quickly learned that the local D-STAR repeaters, although capable of gateway connections, do not necessarily permit them! At least, not to casual users. I can see that the best local repeater is always linked to a certain reflector. When I attempt to change the reflector, I get an error icon.

It didn’t take long to realize it is poor etiquette to show up on a repeater and change the reflector that many folks are monitoring! Bad idea. Now what?

And the answer is…DVAP

No Problem. I just need to be a D-STAR Gateway!

There’s a gizmo for that! What I need is a Digital Voice Access Point or DVAP. The DVAP is an internet gateway interface that can be accessed via UHF simplex. Through the DVAP, I will have my own D-STAR gateway functionality. I wouldn’t rule out a full blown D-STAR repeater sometime in the future, but for now the simplex UHF DVAP will get the job done.

Enter the ZUMSpot.

ZUMspot Kit Features:

  • High performance 32-bit ARM processor
  • ZUMspot Board Fully Assembled And Tested
  • Supports DMR, P-25, D-Star, System Fusion and NXDN
  • Onboard LEDs to show status (Tx, Rx, PTT, Mode)
  • Up to 10mW RF power
  • SMA antenna connector, UHF antenna included
  • Mounts cleanly on all current Raspberry Pi’s including the Pi Zero WH
  • Works on ODROID boards
  • The firmware is pre-loaded and is easily upgraded via software.
  • Connections for Nextion LCD display and I2C displays
  • 1 Year Warranty
  • Open source firmware (MMDVM) and board design
  • Open source 3D printable case available
  • 144 MHz, 220MHz and 900MHz versions to be released at a later date

I am very pleased with the D-STAR Kenwood TH-D74A, and with the overall D-STAR experience thus far, although I am still learning the radio and studying the manual. The APRS performance is also outstanding. I’ve only scratched the surface of this radio’s capability.

The programming of the ZUM hotspot looks pretty straightforward. The DVAP will be included in the 2018 radio hardware upgrade taking place next month.

QSO w/ Scotland via local D-STAR repeater
QSO w/ Scotland via local D-STAR repeater

Pictured above: A QSO in progress with a mobile station in Scotland. He has a multimode hotspot in his vehicle so he can work the world on his way to work!

D-STAR is an exciting new facet of amateur radio here in the K6HR shack!

Back to the front…

Author: K6HR

Licensed since 1994. Active on HF / VHF / UHF / Satellite

Leave a Reply